Neutrik NMJ2 HC-S

389

Jack panel socket

  • 6.35 mm
  • Mono
  • Not switchable
  • With chrome sleeve and standard solder terminals
Myynnissä vuodesta Toukokuu 2010
Tuotenumero 248565
Myyntierä 1 kappaletta
Installation Yes
Mono/Stereo Mono
Angled No
Type TS (mono/unsym.)
Plug Jack 6,3 mm TS female straight
1,20 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu lähetyspäivä Perjantai, 26.04. mennessä
1

389 Asiakkaiden arviot

4.6 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

111 Arvostelut

E
Laadukkaampiakin saa.
ErkkaK 13.05.2014
Liitin vaikuttaa jo paketista tullessaan halvalta. Runko on aika rimpulan oloinen. Liittimen jalat sulavat helposti irti rungosta jos lämmittää vähänkin liikaa. Jalat ovat myös käytännössä irtonaiset, eli kontakti jakkiin saattaa katketa.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

A
Ok connector
Tuntematon 31.03.2017
The connectors work ok, but durability isn't what I expected. The threads in which the metal part (shown in the product picture) connects to is all plastic, and not very durable kind. I messed one connector's threads when I tried to tighten it a bit askew. Other than that I have no complaints.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
t
Cheap, cheerful and good
tremblox 04.11.2021
I've used 5 of these on DIY project recently and have used more of them in the past. What I like is that because of the plastic construction you are not forced to tie the cable shield to the (metallic) enclosure housing. As such this let's you "float" your housing if you prefer (e.g. it provides lower noise levels). One has the choice of course to make a wired connection to the case if desired. the noise benefits.

These plastic units feel cheap, and they are. A little care is needed in soldering to them: apply too much heat for too long to the lugs and you'll start to melt the plastic that holds the lugs in place. So take care.

I don't know how these will stand up over the eons. The ones that I've had on commercial pedals and on my own have stood the test of time and I've had no intermittent contacts so they do seem to be robust. I could imagine that kicking a straight jack plug that has been inserted into this socket could cause some problems, (plastic cracking?) but I haven't experienced this yet. By the same token it probably pays not too over tighten the mounting nut as one would surely strip the plastic threads.

So treat it with care and you'll be rewarded with a vast bang for your buck.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
HT
Good Fit
Harmonic Tonic 19.10.2017
This socket was to replace one in my guitar amp which broke after a lead was tripped over and hence cracked the original.
These sockets always seem a bit light and insubstantial, but I have replaced
them a few times before and they don't really need to be built of hardened steel or
titanium as such. This was for a Roland cube and while I couldn't get it on to
the board in the same way the original socket was on, I still got it on in a
sturdy fashion which should hold for long time, assuming of course it doesn't
get yanked again! I had to use the three washers that came with it to get it to fit the amp casing and it looks well, even better in fact than the original which was all black plastic whereas this has a chrome nut.
So it works fine for me and the price is good too
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta