Millenium RW-2001

285

19" Carriage with Rollers

  • Solid 12U construction with adjustable 8U bottom
  • Load bearing capacity up to 35 kg
  • Height: 120 - 140 cm
  • Width: 65 cm
  • Depth: 60 cm
  • Weight: 7.8 kg
  • Colour: Black

Note: Delivered unassembled.

Myynnissä vuodesta Marraskuu 1999
Tuotenumero 129415
Myyntierä 1 kappaletta
usable height in U 20 U
Material Steel
Wheels Yes
Type Trolley
Height min. 1200 mm
Special Design Frame Construction, Rotatable Top
Height max. 1400 mm
Weight 8,3 kg
Näytä enemmän
66 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Tiistai, 9.04. - Keskiviikko, 10.04.
1

285 Asiakkaiden arviot

4.1 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Vakaus

Työnjälki

146 Arvostelut

JJ
Hutiloiden tehty ja käyttökelvoton
Jussi J. 08.02.2015
Kasaaminen oli helppoa ja renkaat olivat tukevat.

Alaräkki oli kohtuullinen, joskin ruuvit ovat täysin epästandardeja väleiltään - kaikki laitteet tulivat vain kahdella ruuvilla kiinni koska vain ylä- tai alaosa kiinnitysrei'istä näkyy. Ironista kyllä, Behringerin jakaja ei mahtunut kiinni kukn yhdestä kulmasta koska nyös siinä oli epästandardit ruuvinkohdat. Kyllähän se muiden laitteiden välissä pysyi paikallaan.

Yläräkkiin en valitettavasti saanut mahdutettua Mackien 16 kanavaista mikseriä koska ruuvit ovat väärissä väleissä jotta räkkiraudat voisi kiinnittää. Ja lisäksi rakenteen perseilystä johtuen pitää olla todella pitkät ruuvit koska mikseri jää noin sentin korkeuteen ylätelineestä. Eli yhdellä ruuvilla kiinni ja piuhat vetävät mikseriä? Ei kiitos. Ruuvinreiät siis eri korkeudella telineen vasemmalla ja oikealla puolella.
Vakaus
Työnjälki
2
0
Raportoi ongelmasta

Raportoi ongelmasta

A
Erittäin kätevä
Tuntematon 12.10.2016
Tällä hetkellä räkissä kiinni:
1x the t.racks DS 2/4 B-Stock
1x Behringer iNuke NU6000
1x Phonic IAMP 3020 DSP

sekä taittuvan päällys osan päälle laitoin vähän levyä kiinni niin sain sopivan tason mixerille.

Behringerin vahvistimen kanssa teki hieman tiukkaa laittaa kaikki ruuvit paikalleen, mutta avasin vähän alatuen ruuveja auki jolloin sain paremmin vahvistimen kiinni. Ruuveja tuli mukana yllättävän vähän, ei riittäneet edes tähän kaikkeen, mutta kyllähän niitä lisää saa.
Vakaus
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
K
Awesome Rack
Kitapci 02.10.2014
I use this to mount a Behringer Xenyx 2442fx (located in the top adjustable angle rack) with rack gear such as headphone amplifiers, gates, reverb, ect along the bottom rack. This comes with plenty of places to mount rack equipment and is especially useful if you have a lot of them. My band uses our own small set up for band rehearsal but being the drumming it was a bit awkward having the mixer in accessible reach to change any monitor mixes on the fly, luckily with this I was able to bring the mixer and the outboard gear much closer when at the drums and push it neatly away when band practice had finished.

I can also see this being very useful in a home studio set up that lacks a patch bay as it is much easier to move this around and get to the back of equipment than in a usual cabinet of rack equipment.

However there is an issue with this style rack, since its not a cabinet all of the cabling is on show so unless you have velcro cable ties it can look a bit messy and can often run over cables on the ground when moving around if you're not looking.
Another issue isn't with the product but rather with the manufacturer; it doesn't come with any instructions which does mean you have to figure it out as you go, but even with that it only took around 5-10 minutes to build.

Over all its a great product and very good price point.
Vakaus
Työnjälki
3
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
DJ
Disappointing purchase
Derek J. 12.11.2013
Screw holes in the top section of the rack were unevenly placed resulting in racks that were lopsided 0mm on the left and 4mm! on the right. One of the rack spaces was unusable. Had to experiment with the placement of my various rack units (1U, 2U, 3U) to get them into the rack. Very frustrating. I understand this is a cheaply priced unit. but misaligned screw holes is totally unacceptable. Minor observation - when assembled the using didn't sit flatly on the floor - one of the wheels had to be adjusted substantially to stop the unit rocking.
Vakaus
Työnjälki
7
0
Raportoi ongelmasta

Raportoi ongelmasta