Jaspers Monitor Holder 60B

17

Monitor Holder

  • Tube length: 60 cm
  • Holder: 30 cm
  • Maximum load: 7 kg
  • Colour: Black powder-coated
  • Can be mounted at any point with 2-piece T-connectors, without having to disassemble the stand
Myynnissä vuodesta Syyskuu 2006
Tuotenumero 187591
Myyntierä 1 kappaletta
Type Of Keyboard Stand Monitor Holder
Colour Black
66 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Tiistai, 9.04. - Keskiviikko, 10.04.
1

17 Asiakkaiden arviot

4.8 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Vakaus

Työnjälki

10 Arvostelut

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
s
Nice add on for the Jasper Racks
sean32767 15.05.2017
I bought these to hold smaller gear on the side of my Jasper rack (a Tempest drum machine and a desktop synth).

Worked great for the intended purpose, although I find the attaching / adjusting to be a bit of a hassle. Make sure you have it set right before tightening everything and it will be fine!
Vakaus
Työnjälki
1
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
Mf
Solid, and exactly what I was looking for
Mick from Belfast 03.06.2021
Having tried for some time to optimise my 3 keyboard rig, with one of those keyboards being a Roland JDXi, I have finally found what I was looking for. As a keys player who prefers to sit rather than stand, I've never liked a 3 level rig (the JDXi being the smallest was sitting at the top of that rig) but I could never find a small enough single stand that would enable me to place the JDXi to my left, and at the right level.

Enter this product which, in combination with a small speaker stand which I picked up for £15, gives me a really solid (and easily portable) stand for the JDXi. To do this I simply had to spin the T joint 90 degrees and place it in the centre of the main bar (so it could be set on to the speaker stand), while the support arms can then be placed anywhere to support the keyboard. No more creaking of my neck to read the control panel on the JDXi!!!!

Overall, great solution to my needs.
Vakaus
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
V
Useful Accessory
VinceL 30.07.2013
I use this to support a tone generator rack between two keyboards, and does this very well. The only slight problem is that it is only supported at one end, so may tend to droop. No danger of it falling off though.
Vakaus
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta