Sivun sisältöön

Harley Benton Parts Neckplate Screw Set

16

Set of Neck Mounting Screws

  • 4 x 2 x 45 mm
  • Colour: Chrome
  • Quantity: 4 pieces
Myynnissä vuodesta Lokakuu 2022
Tuotenumero 538276
Myyntierä 1 kappaletta
1,66 €
Sis. ALV. Ei sisällä 5,90 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Maanantai, 17.02. - Tiistai, 18.02.
1

16 Asiakkaiden arviot

4.6 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

8 Arvostelut

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
FB
Wrong for my guitar
Francesco. B. 23.01.2025
I dismantled my HB 20 HSS for safe air travel and managed to lose the neck screws in the process. I ordered these and when I went to fit them they were too short and loose. Had to use different screws from a hardware shop which were a bit thicker and longer. 4 stars for fast delivery and the fact that they seem excellent quality
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
M
great screws
Merijntz 16.01.2025
They keep a good firm hold on your guitar neck and its good quality, they also fit on many of my guitars like a strat a tele and a V
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate fr
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
MM
Vis parfaites
Michel Mike 22.02.2024
longueur totale 45.2mm; diamètre tête 7.8mm; diamètre partie filetée 4.17mm : il est important de forer les 4 trous du "neck pocket" à 4.2 ou 4.5mm, il doit y avoir un léger jeu qui permet l'alignement parfait du manche avant serrage. Le manche tient exclusivement grâce à la force exercée entre les têtes des vis contre la plaque de manche à l'arrière du "neck pocket" et les extrémités des vis qui prennent dans le talon du manche. Je perce des trous pilotes de 3mm de diamètre et de 13.5mm de profondeur dans le talon du manche, et je passe l’extrémité des vis à la cire. NOTE: ces mesures correspondent à un corps de 44.5mm d'épaisseur avec un "neck pocket" de 16 mm de profondeur (Telecaster classique). Ces vis tiennent parfaitement leur rôle.
Työnjälki
6
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate de
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
H
Top
Hulzmichl 02.05.2023
Brauchte diese Schrauben als Ersatzteile für meine alte Strat. Sie machen was Sie sollen.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta