Harley Benton Elec.Guitar Machine Head ST CR

168

Machine Head Set for Electric Guitar

  • ST-Style chrome Machine Head Set for Electric Guitar
  • 6 In line
  • Small button
  • Bore diameter 10 mm
  • Chrome-plated
  • Ratio: 1:14
Myynnissä vuodesta Kesäkuu 2010
Tuotenumero 250914
Myyntierä 1 kappaletta
Colour Chrome
19,30 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu toimituspäivä Keskiviikko, 24.04. - Torstai, 25.04.
1

168 Asiakkaiden arviot

4.4 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

85 Arvostelut

TH
Perusvirittimiä paremmat
Tero H. 02.07.2014
Hieman epäilevin mielin tilasin nämä halvimman hintaluokan tarvikevirittimet, mutta paketin saavuttua ja näitä tutkittuani totesin niiden olevan aivan kelpo virittimet. Valurungon ja tukevan rakenteen myötä on kielten virittäminen helpottunut paljon. Kaikki kuusi ovat tuntumaltaan täysin samanlaiset, eikä vire karkaa kesken soiton. Asennuskin sujui helposti.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
BI
Weak screws but excellent machine heads
Benjamin I. 03.02.2019
When I opened the package the miniature screws that go to the back of the headstock seemed thin and fragile; the heads, on the other hand, looked tough and accurately made. Their heft suggests a solid build. Turning them showed no play, but would that be the same under tension? Their shape is consistent, none of them have burrs, rough edges, mis-shaped parts or whatnot, and the chrome-plating is even, so a very good first examination.

The older heads on my Affinity Fender had a slightly thinner frame, and some play, you can feel that when you turn them back and forth a little. The mounting holes in the wood were oversize, so the heads tilted, and with string pull and me tightening the hex bolts, their frame split.

So I ordered these replacements. Before the switch I shimmed the heads with masking tape so they won't play in the mounting holes. I must say I like how they are built, the hex bolt is taller and stronger, it's easy to tighten in a controlled manner. But the tiny screws on the back are too thin for their mounting holes, so the heads can pivot, and that causes them to be visibly not square with the side of the headstock.

So I put in screws with the same head (PH1 screwdriver) but a thicker body, and the pivoting stopped. I always recover screws from the appliances I send to recycling so I have plenty of screw types. Well, after installing the heads and the strings (0.10), the heads still don't play, even under tension. They are not too firm of too loose, just right.

The pegs are 3mm longer than the stock Affinity heads but that's not an aesthetic problem, lots of my other guitars have longer pegs, too. The washers are smaller and that looks better to my eye.

After the damage in my Affinity I checked my other guitars, and a couple of them have tilted heads because of oversize mounting holes, so I will shim them when I change the strings, and if some heads snap again, I will use these Harley Benton's to replace them. I was not sure the bottom-price heads would be super tight but for an unexpensive guitar I took bottom-price accessories. I don't regret it, except for the tiny fragile screws (two broke when I tightened them a bit too hard) that can be swapped, the machine heads are very good.

I thought all the affordable guitars had to have some play in their heads but that's not true. I recommend them but, Thomann, please deliver them with stronger screws.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
A
OK for what they are
AusSparky 10.02.2019
They are pretty cheap so you can't expect much, but they do the job.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
WW
Ok tuners
Wilson WIlsonson 03.02.2021
Installed on my project guitar.
Based on the cheap price, one would assume that the tuners won't hold the tune, but they do their job well enough. Haven't played full gigs, but after several songs, there was no need to retune.
Precision is good enough too for the price. It is possible to tune the guitar fast enough.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta