EMG 1 or 2 Pickups HZ Wiring Kit

14

Pickup installation kit

  • With everything you need to install 1 or 2 passive EMG solderless pickups
  • Contains potentiometers with corrugation axis (standard length)
  • 2 Volume potentiometers
  • 2 Clay potentiometers
  • 1 Pickup bus
  • 1 Power bus
  • 1 12B Output socket with battery clip
  • 1 Output cable
  • 4 Interconnect cables
  • 2 Pickup cables
  • Only suitable for passive pickups!
Myynnissä vuodesta Elokuu 2016
Tuotenumero 391886
Myyntierä 1 kappaletta
45 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu lähetyspäivä Lauantai, 30.03. mennessä
1

14 Asiakkaiden arviot

4.9 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

10 Arvostelut

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
A
Used it with EMG 40HZ set
Tuntematon 30.03.2017
I bought a set of EMG 40HZ for a bass and since I didn't wanted to bother with all of the soldering I decided to go with EMG's solderless install (40HZ didn't included any of the quick install components, unlike active EMG pickups).

The whole idea with a solderless install is really great. It took me less than 15 minutes to get everything working.
Default connectors are wired for serial humbucker connection. But with spare EMG connector cable and 2-pin connectors you can easily change the connection type (I got 2 spare cables with my pickups that was used for split-coil hum-cancelling connection type).

Wiring kit is also compatible with any other passive pickups. The only thing you need to get it working is connecting 2-pin connector to the pickup cable instead of soldering it.

The only downside of the Wiring Kit I got, was the wrong wiring on one of the pickup cables. It took me a while until I finally measured pickup resistance on the connection cable and understood that 2 wires on the connector were out of place and pickup was working in single coil mode as a result. Fortunately it wasn't too hard to switch a few wires and get a perfectly working humbucker in the end.

I think this was just an isolated error, but in case anyone got some volume problems - check cable wiring first.
Työnjälki
3
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
B
Brilliant for installing EMG PHZ set
Basspower50 14.01.2019
I purchased a set of EMG PHZ pickups, however I found the included cable a little bit short to reach from the base of the pickup to the volume/tone controls (weird!). Anyway, I bought this and it came with absolutely everything I needed to complete the installation. Very happy and I would recommend to anyone who encounters a similar issue.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
LO
Managed 2 guitars
Lord O 07.09.2022
Bought this to rewire 2 Ltd guitars I bought years ago that some gorillas had seemed to rewire themselves. One had the quick connect on the pickups themselves so used the included cables. Managed to put Dupont connectors on the others and it worked well. All the components in the kit were good quality and went together easily.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
P
Makes life so easy !
Paul.7 16.10.2022
These solderless connections are a gane changer ! Plug and go
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta