Adam Hall 5651 Rack Nut Pack

295

Cage Nut

  • For rack rails with square punching
  • M6 Thread
  • 20 Pieces per pack
Myynnissä vuodesta Huhtikuu 2011
Tuotenumero 263171
Myyntierä 1 kappaletta
Type Cage Nut
Thread Size M6
Amount 20
Note N/A
Näytä enemmän
6,50 €
Sis. ALV. Ei sisällä 12 € rahtikulua
Varastossa
Varastossa

Tuotetta on varastossa ja se voidaan lähettää heti.

Tietoa lähetyksestä
Arvioitu lähetyspäivä Torstai, 28.03. mennessä
1

295 Asiakkaiden arviot

4.8 / 5

Sinun pitää kirjatua sisään, jotta voit arvostella tuotteita.

Huomio: jotta vältymme kuulopuheisiin, epätäydelliseen tietoon tai mainontaan perustuvia arvosteluja, niitä saa tehdä vain asiakas, joka on tuotteen meiltä ostanut.

Sisäänkirjautumisen jälkeen löydät kaikki arvosteltavat tuotteet kohdasta “Arvostele tuotteita” asiakastililtäsi.

Työnjälki

103 Arvostelut

A
Fairly annoying
ApryghnatoR 23.04.2020
EDIT: I'm an idiot, they are supposed to be put in different way... They work very well if placed with retainers horizontally instead of vertically.

I'm not sure should I complain about these, or the Millennium Steel Box Rack I have these in. These were recommended for the rack so I went for it. They do what they are supposed to, but they are a real pain in the *** to get into the rack. They don't go in too well, and once in, they slip out pretty easy. If you are placing one next to another, it's even harder to get them in. Worse is that if you have most of the rack assembled, but one of these end up popping out, you might need to do some unassembling to get it back in place.

All in all, your mileage may vary. They perform fine once in, but can take nerves and a while to get set up.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

L
Must have
Leevivuo 23.06.2021
Handily locks into the rack strip holes. Because they are installed before anything else and stay put on your rack, they are also handy for planning and marking your rack on more complex setups. The nut is captive stays still when you screw into it so installation of panels and equipment is easy. Pushing these into the holes is easier with a pointy tool to bend the clip.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

J
Hyvä räkkimutteri
JohanRM 09.09.2023
Näillä ja Adam Hallin ruuveilla ja räkkikannattimilla olen kiinnitellyt kaikki itse tehtyjen räkkien laitteet kiinni. Näitä pitää olla aina tarvikelatikossa varalla, hyvä ja toimiva tuote.
Työnjälki
0
0
Raportoi ongelmasta

Raportoi ongelmasta

google translate gb
Valitettavasti tapahtui virhe. Ole hyvä ja yritä uudelleen.
Y
Nice nut
Younglad 26.05.2021
I really have no experience with nuts other than these. For me these nuts have worked flawlessly in my rack. No cons.
Very happy with my nut.
Työnjälki
2
1
Raportoi ongelmasta

Raportoi ongelmasta