Rockbag Fingerboard Saver 1 narrow

45

Protector de diapasón

  • Para trastes estrechos
  • Protege el diapasón durante el coronamiento, el lijado o el pulido de los trastes
  • Se adapta a la mayoría de los alambres de trastes estrechos disponibles de forma comercial
  • Encaja entre todos los trastes en guitarras, banjos y bajos
  • Encaja entre la mayoría de los trastes de ukeleles y mandolinas
  • Anchura de la ranura: 1,8mm (0,071")
  • Longitud de la ranura: 70mm (2,76") - también se adapta a la mayoría de los bajos de 5 cuerdas
  • Muescas para la fijación con bandas de goma en el mástil
  • Hecho de acero inoxidable flexible de 0,2mm (0,008")
  • Se adapta al radio del diapasón
  • Dimensiones: 80mm (3,15") x 16mm (0,63") (largo x ancho)
  • Set de 2 piezas, incluyendo bandas de goma
Disponible desde Marzo 2017
número de artículo 406098
Precio por 1 Unidad(es)
Tamaño Small
Número 2
3,40 €
IVA incluido. 15 € de gastos de envío adicionales
En stock
En stock

Este producto está en stock y puede ser enviado inmediatamente.

Información sobre envíos
Previsión de envío el Sábado, 30.03.
1

45 Valoraciones de los clientes

4.6 / 5

Para poder evaluar un producto deber estar registrado en su centro de clientes.

Importante: Con fin de evitar evaluaciones en base a rumores o mitos populares, solo permitimos en nuestro website evaluaciones por clientes que hayan comprado el producto con nosotros.

Tras de acceder a su centro de clientes encuentra en Centro de clientes "Evaluar productos" todos los artículos que puede evaluar.

Fabricación

20 Reseñas

N
Esta bien
Natucas 24.04.2019
sirve muy bien para pulir los trastes sin dañar la madera
Fabricación
0
0
Reportar evaluación

Reportar evaluación

google translate gb
Lamentablemente hubo un error. Por favor, inténtelo de nuevo más tarde.
G
Rockbag Fingerboard Saver 1 narrow
Gammamaster 30.12.2017
Rockbag Fingerboard Saver 1 narrow
Previously I have used the Göldo WS045 Fretboard Guard which measures approximately 80mm x 22mm with a slot that measures approximately 3 mm x 69 mm.
I found the Göldo slot to be too large and so I thought I would try the Rockbag version.
To start with the Rockbag actually contains two guards along with a couple of elastic bands to hold them in place.
The Rockbag fingerboard savers are available in three sizes, this is the narrow version.
The guard measure approximately 80mm x 60mm with a slot that measures approximately 70mm x 1.8mm
The guards are very neatly cut out from 0.2mm thick stainless steel with no obvious rough edges to worry about.
The slot is very narrow and I found it was too narrow for most of my guitars, certainly too narrow for any of my Gibson and most of my Fenders.
It only fitted two Japanese fenders, (a FSR competition stripe mustang and a '62 custom telecaster) both with really narrow vintage style frets.
The guards work well, much better than the Göldo guard and I will be ordering the two other sizes as soon as possible as they are very useful.
Fabricación
0
0
Reportar evaluación

Reportar evaluación

google translate gb
Lamentablemente hubo un error. Por favor, inténtelo de nuevo más tarde.
J
Good enough. What can you say and what would you say
Jpr666 05.02.2021
Its made for a purpose and does it well.
There is not much more to add.
Handy discovery if you had never heard of it. And they last....I use them quite a lot.
Fabricación
0
0
Reportar evaluación

Reportar evaluación

google translate gb
Lamentablemente hubo un error. Por favor, inténtelo de nuevo más tarde.
AK
?Simple thing, tricky to ues
Alfred Kyy 17.02.2020
This does the thing it should do; protects your fingerboard when filing or polishing your frets.

The hard part is use rubber bands to hold it on its place. I usually end up holding it by hand instead of using rubber bands. Holding this is easier if you add some duct tape to sides to make it a bit bigger and easier to hold.
Fabricación
0
0
Reportar evaluación

Reportar evaluación