Kundecenter log-in
Land og sprog Country and Language

Klark Teknik Mic Booster CT1

64

Dynamic Microphone Booster

  • For dynamic or passive ribbon microphones
  • Gain: 25 dB
  • Power supply via phantom power
  • Frequency range: 10 - 20,000 Hz (± 1 dB)
  • Input and output: XLR
  • Dimensions: 24 x 25 x 78 mm
  • Weight: 100 g
Channels 1
Number of microphone inputs 1
Instrument input No
Tubes No
Compressor/Limiter No
Equalizer No
De-Esser No
Phantom power Yes
Phase Reverse No
External effect loops No
Analogue Outputs XLR
Digitale Outputs 0
Headphone connection No
Level Meter No
Artikelnummer 474739
169 kr
Inkl. moms plus 60 kr forsendelse
Tilgængelig
Tilgængelig

Varen er på lager og kan afsendes med det samme.

Information om forsendelse
Forventet levering mellem onsdag, 27.10. og torsdag, 28.10.
1
9 Salgsrang

64 Kundeservice

5 49 Kunder
4 8 Kunder
3 3 Kunder
2 4 Kunder
1 0 Kunder

betjening

features

lyd

forarbejdning

google translate gb
Der opstod en fejl. Prøv igen senere.
j
Awesomely convenient and does the job!
jvranopa 20.08.2021
It's so nice to have a booster that can directly be attached to the mic rather than having to connect an extra XLR wire. I'm using a Scarlett 2i2 as well as my newly arrived Shure SM7B. So far, it does the job splendidly. The boost is quite helpful and clean. No need to dial way up on my Scarlett 2i2. I would definitely recommend this booster for the price! Just a small caveat though: I work at a place with a radio station, so it picks up a bit of the transmission, but it's too quiet to be noticeable. It can easily be removed using a noise remover on your DAW. The vocals are pretty clean regardless. Go and get this!
betjening
features
lyd
forarbejdning
0
0
Anmeld bedømmelse

Anmeld bedømmelse

google translate gb
Der opstod en fejl. Prøv igen senere.
C
It's cleaR, but not cleaN
CyberDNIWE 06.06.2021
Converting 48v phantom power into "clean" gain is ok, but
compared to Behringer UMC202HD's midas preamps, this thing is noisy. However, the noise seems to be not the typical high pitched whine of preamps, but rather a little bit lower one.

You also need a patch cable to connect it directly to the interface, because the male part has a very thick layer of metal around it and would siply not fit. Respectively, if you're ok with plugging it in the back of the mic, then no extra cables are required.

Conclusion:
If you have a decent enough preamp in your interface you dont need it. If you dont, then you probably will not care about a few extra db of background preamp noise. In the end, it does what it advertises to do, and for the price, it is enough.
betjening
features
lyd
forarbejdning
0
0
Anmeld bedømmelse

Anmeld bedømmelse

google translate gb
Der opstod en fejl. Prøv igen senere.
S
Bang for the buck
S-fin 20.08.2021
Very good mic booster for the price. Use it with my t.bone mb7 b and focusrite scarlett solo. Amps the mic gain up just the right amount that I don't have to crank the boost knob too high. Only problem seems to be that you have to pretty much have 2 xlr cables because this devise is built weirdly. Other end won't go straight to scarlett solo and the other doesn't quite seem to fit to the microphone. Other than that, I have nothing bad to say about this.
betjening
features
lyd
forarbejdning
0
0
Anmeld bedømmelse

Anmeld bedømmelse

google translate gb
Der opstod en fejl. Prøv igen senere.
Pretty good
G 13.07.2021
This mic booster doesnt introduce much noise at all, the noise that is presented is just noise i heard from my amp being boosted. It lasted until i wanted to move on from the rode podmic and continues to work exactly as it did when i got it. if youre into dynamic mics this is one of the absolute best options for an inline preamp
betjening
features
lyd
forarbejdning
0
0
Anmeld bedømmelse

Anmeld bedømmelse

YouTube på dette emne

Rådgivning