K&M 23325 Table Microphone Stand

328

Microphone Stand

  • Black
  • Cast-iron base with special rubber insert for silencing
  • Screwed, adjustable tube combination
  • Weight: 2.5kg
  • H: 217-347 mm
  • Base-Ø 180 mm
K dostání od Červen 2013
Číslo produktu 316056
Prodejní jednotka 1 ks
Type Desk stand
Colour Black
845 Kč
Cena vč. DPH nezahrnuje poštovné 295 Kč
Na skladě
Na skladě

Tento produkt je na skladě a může být obratem odeslán.

Informace o expedici
Odešleme pravděpodobně do Čtvrtek, 25.04.
1

328 Hodnocení zákazníků

4.8 / 5

Musíte být přihlášeni, pokud chcete hodnotit produkty.

Upozornění: Abychom zabránili tomu, že se budou hodnocení zakládat informacích z doslechu, polovičních pravdách nebo skryté reklamě, dovolujeme na našich stránkách hodnotit pouze skutečným uživatelům, kteří u nás vybavení také koupili.

Po přihlášení najdete také v zákaznickém centru v sekci "Hodnotit produkty" všechny produkty, které můžete hodnotit.

Ovládání

Stabilita

Zpracování

188 Recenze

google translate gb
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
DD
Feels heavier & sturdier than the photo!
Dr D 01.11.2019
I have a heavy RODE Procaster with shockmount plus TritonAudio Fethead and windshield attached, so I was concerned that a relatively short desktop stand with a not so big base circumference (180 cm or 6-inches) would suffice. Thankfully, I can report that this K&M mic stand is absolutely perfect. It is really quite heavy @ 2.5 Kg ( > 5 lbs) weight, thus can easily cope with more than a kilo of weight up top. In fact, when I grab the head of the mic whilst attached to this stand and try and pull it or tip it over, it just will not.
The other cool aspect of this particular mic stand, is the easily adjustable telescopic pole to adjust the height of the mic. Although it does not increase the overall height by that much, it is sufficient to get the mic up to head head whilst seated at a desk with this stand in front of you. It also secures very well and does not slip or move at all.
Finally, the circular rubber inlay on the rear side of the base, just feels quality - soft but does not allow the stand to slide at all. Even hitting the side of the base with my clenched fist does not move it.
I would highly recommend these K&M mic stands and the next time I shall be in the market for another one, I will look for this brand again.
Ovládání
Stabilita
Zpracování
3
1
Ohlásit hodnocení

Ohlásit hodnocení

google translate gb
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
N
Doubles as a battel hammer
Nänad 04.01.2021
Seriously, this thing is so sturdy, you can kill a guy with it. Has a rubber layer on the bottom which prevents it from sliding on top of a desk. RODE NT 1 fits perfectly on top of it. Can be used for recording instruments, but for recording conversations as well...and killing people (in which case RODE NT1 should be replace with Shure SM58, due to it's enhanced rigidness)
Ovládání
Stabilita
Zpracování
8
1
Ohlásit hodnocení

Ohlásit hodnocení

google translate gb
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
r
Its decent
rayzer... 03.04.2022
It has a really heavy base so you wont be knocking it over accidentally but i found it sounded a bit hollow when i first used it by my computer.
After sticking some carpet and rubber squares under it that became a non issue.
Other than that its sturdy and does its job.
Ovládání
Stabilita
Zpracování
0
0
Ohlásit hodnocení

Ohlásit hodnocení

google translate gb
Bohužel se vyskyla chyba. Zopakujte protím tuto akci později.
AD
Nothing not to like.
A Dutch Person 11.01.2021
Reassuringly heavy, thank god. You can extend it 15 cm (unlike the K&M 232BK) which is great. It has a sturdy rubber ring at the bottom to dampen vibrations. It feels rock solid and I will probably also use it for live music (with omni and cardiods) in small interior locations (on table, shelf or chair) when there is no room for mike stands. They won't fall over.
Ovládání
Stabilita
Zpracování
0
0
Ohlásit hodnocení

Ohlásit hodnocení