Rockbag Fingerboard Saver 1 narrow

45

Fingerboard Saver for Thin Fret Wire

  • Protects the fretboard during crowning, filing or polishing of the frets
  • Fits on most thin fret wires
  • Fits between all frets on guitars, banjos and electronic basses
  • Fits between most mandolin and ukulele frets
  • Slot widths: 1.8 mm (0.071")
  • Slot length: 70 mm (2.76") - also fits most 5-string basses
  • Notches for fixing with included rubber bands on the neck
  • Made from flexible 0.2 mm (0.008") stainless steel
  • Adapts to the fingerboard radius
  • Dimensions (L x W): 80 mm (3.15") x 16 mm (0.63")
  • Set of 2 pieces including rubber bands
Available since March 2017
Item number 406098
Sales Unit 1 piece(s)
Size Small
Amount 2
3,44 €
Including VAT; Excluding 5,90 € shipping
In stock
In stock

This product is in stock and can be shipped immediately.

Standard Delivery Times
Dispatch expected by Thursday, 28.03.
1

45 Customer ratings

4.6 / 5

You have to be logged in to rate products.

Note: To prevent ratings from being based on hearsay, smattering or surreptitious advertising we only allow ratings from real users on our website, who have bought the equipment from us.

After logging in you will also find all items you can rate under rate products in the customer centre.

quality

20 Reviews

G
Rockbag Fingerboard Saver 1 narrow
Gammamaster 30.12.2017
Rockbag Fingerboard Saver 1 narrow
Previously I have used the Göldo WS045 Fretboard Guard which measures approximately 80mm x 22mm with a slot that measures approximately 3 mm x 69 mm.
I found the Göldo slot to be too large and so I thought I would try the Rockbag version.
To start with the Rockbag actually contains two guards along with a couple of elastic bands to hold them in place.
The Rockbag fingerboard savers are available in three sizes, this is the narrow version.
The guard measure approximately 80mm x 60mm with a slot that measures approximately 70mm x 1.8mm
The guards are very neatly cut out from 0.2mm thick stainless steel with no obvious rough edges to worry about.
The slot is very narrow and I found it was too narrow for most of my guitars, certainly too narrow for any of my Gibson and most of my Fenders.
It only fitted two Japanese fenders, (a FSR competition stripe mustang and a '62 custom telecaster) both with really narrow vintage style frets.
The guards work well, much better than the Göldo guard and I will be ordering the two other sizes as soon as possible as they are very useful.
quality
0
0
Report

Report

J
Good enough. What can you say and what would you say
Jpr666 05.02.2021
Its made for a purpose and does it well.
There is not much more to add.
Handy discovery if you had never heard of it. And they last....I use them quite a lot.
quality
0
0
Report

Report

AK
?Simple thing, tricky to ues
Alfred Kyy 17.02.2020
This does the thing it should do; protects your fingerboard when filing or polishing your frets.

The hard part is use rubber bands to hold it on its place. I usually end up holding it by hand instead of using rubber bands. Holding this is easier if you add some duct tape to sides to make it a bit bigger and easier to hold.
quality
0
0
Report

Report

R
Quality All Around
Robbob 02.03.2024
Ordered the full set but 1 was missing due to a whole in the box when received. Quick e-mail to the service department and the one missing was on the way. Great products and support. What more can you ask for.
quality
0
0
Report

Report