One Control Minimal Series White Loop

59

2 Channel Looper

  • 2x 9V outputs
  • True bypass
Notera Register your purchase at www.w-distribution.de/en/Warranty for an extended warranty of 4 years.
Tillgänglig sedan Februari 2016
Artikelnummer 382075
försäljningsenhet 1 Styck
Type Looper
LED Display Yes
PSU Connector Yes
Shape Floor Effects Pedal
MIDI Interface No
929 kr
inklusive moms, 99 kr frakt tillkommer
i lager
i lager

Produkten finns i lager och kan levereras omgående.

Information om leveransen
Leverans beräknas mellan Onsdag, 24.04. och Torsdag, 25.04.
1

59 Kundbetyg

4.6 / 5

Du måste vara inloggad för att kunna betygsätta en produkt.

Obs! För att undvika att betygsättningen är byggt på rykten eller smygreklam kan bara kunder som har köpt produkten från oss sätta sitt betyg.

Efter inloggningen i kundcentret kan du se vilka produkter som kan betygsättas.

funktioner

hantverkskvalitet

44 Recensioner

H
Petfekt för 2 extra "drive" kanaler.
Hellurei 01.03.2024
Suveränt att genom en knapp tryckning ha 2 st pedal slingor att hantera med samt den andre knappen som "by pass" funktion. Mycket användbar och prisvärd produkt.
funktioner
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

A
Gör sitt jobb
Anonym 06.12.2016
Smidig och användbar som gjorde det som framgick i informationen.
funktioner
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
GP
Great features... lacks quality
Gus Posada 16.02.2020
>Use
For recording studio.

>Connection
Input: Guitar to Chain of analog effects.
Green loop: class A Fender Tweed preamp + Modulation effects
Red loop: Diezel VH4 preamp + Modulation effects
Output: Mesa power amp + Palmer 2x12 Closed Back Cabin

>Facts
I have noticed that noise is being induced from Green to/from Red loops. I use an isolated 9 volt DC adaptor, as for each loop's chain of effects; none of the two extra 9V DC / OUT are being used. Still, ground, hum and hiss affect the Output signal.

>Test
Input: Guitar
Green Loop Send: none
Green Loop Return: out from chorus pedal with 9v batt
Red Loop Send-Return: sealed jumper cable
Output: Amp
Procedure: turn on the switch, set loop red (jumper), turn on the chorus pedal, listen to how the Amp captures the signal effect from the chrous pedal even while a different loop is being used. turn off the chorus pedal and unplugged it form the device. listen how the guitar signal is affected by the loop, even while using a jumper cable (buffer?).
funktioner
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
v
Nice beautiful helper pedal
vladg 15.09.2016
If you have 2 parallel signal chains and want to switch between them in 1 click, this pedal is for you.

For example:
distortion1 -> delay1
distortion2 -> delay2

Now you connect the 1st chain as the 1st loop, the 2nd chain as the 2nd loop (send/return) into the pedal, and now you can switch between them! Also the processing can be bypassed. But I use this pedal to switch between 2 preamps that don't have bypass so they can't be connected in series.

The pedal looks just beautiful and due to white color it's easy to find it on a pedal board.

Also the switches are mechanical and of good quality. It also means the pedal can operate without voltage applied to it! 9V used to light up LEDs. It's really useful if you're out of power cords. Also the pedal offers 9V pass-through, which can be helpful too.

EDIT: when trying to loop high-gain distortion pedal the crosstalk between send and return, amplified by high gain dirstortion leads to feedback whistle. The pedal is unusable in this case.
funktioner
hantverkskvalitet
1
0
Anmäl recension

Anmäl recension