Neutrik NMJ2 HC-S

389

Jack panel socket

  • 6.35 mm
  • Mono
  • Not switchable
  • With chrome sleeve and standard solder terminals
Tillgänglig sedan Maj 2010
Artikelnummer 248565
försäljningsenhet 1 Styck
Installation Yes
Mono/Stereo Mono
Angled No
Type TS (mono/unsym.)
Plug Jack 6,3 mm TS female straight
13,90 kr
inklusive moms, 99 kr frakt tillkommer
i lager
i lager

Produkten finns i lager och kan levereras omgående.

Information om leveransen
Leverans beräknas mellan Onsdag, 24.04. och Torsdag, 25.04.
1

389 Kundbetyg

4.6 / 5

Du måste vara inloggad för att kunna betygsätta en produkt.

Obs! För att undvika att betygsättningen är byggt på rykten eller smygreklam kan bara kunder som har köpt produkten från oss sätta sitt betyg.

Efter inloggningen i kundcentret kan du se vilka produkter som kan betygsättas.

hantverkskvalitet

111 Recensioner

IA
Stabil!
Ingemar A. 13.06.2015
Köpte denna till ett högtalarkabinett där den sitter monterad på en 3mm aluminiumplåt vilket passade perfekt. Sladdarna monterade jag med kabelskor med 4,8mm bredd som passade bra. Högtalarkabeln sitter stabilt och bra!
hantverkskvalitet
1
0
Anmäl recension

Anmäl recension

S
Klen!
SusanneJ 11.03.2017
Nu är jag van att löda men den här kontakten är inte så lätt att ha att göra med.
Anslutningsblecken behöver inte bli så varma innan plasten på kontakten börjar att smälta.
Köp en kontakt som bara är gjord i metall i stället!
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

b
Löser problemet
bellasoda 02.04.2021
Kabeln sitter inte superbra i hålet, känns lite glappt. Andra kontakter jag provat har varit stabilare.
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension

google translate gb
Tyvärr uppstod ett fel. försök igen senare.
t
Cheap, cheerful and good
tremblox 04.11.2021
I've used 5 of these on DIY project recently and have used more of them in the past. What I like is that because of the plastic construction you are not forced to tie the cable shield to the (metallic) enclosure housing. As such this let's you "float" your housing if you prefer (e.g. it provides lower noise levels). One has the choice of course to make a wired connection to the case if desired. the noise benefits.

These plastic units feel cheap, and they are. A little care is needed in soldering to them: apply too much heat for too long to the lugs and you'll start to melt the plastic that holds the lugs in place. So take care.

I don't know how these will stand up over the eons. The ones that I've had on commercial pedals and on my own have stood the test of time and I've had no intermittent contacts so they do seem to be robust. I could imagine that kicking a straight jack plug that has been inserted into this socket could cause some problems, (plastic cracking?) but I haven't experienced this yet. By the same token it probably pays not too over tighten the mounting nut as one would surely strip the plastic threads.

So treat it with care and you'll be rewarded with a vast bang for your buck.
hantverkskvalitet
0
0
Anmäl recension

Anmäl recension