Harley Benton DC-Ukulele CH

191

Concert Ukulele with Pickup

  • Double cut design
  • Basswood body
  • Set-in maple neck
  • Laurel fretboard
  • 18 Frets
  • Scale: 380 mm
  • Vintage-style machine heads
  • Built-in piezo pickup
  • Volume and tone controls
  • Colour: Cherry high-gloss
  • Includes a gig bag
  • Matching case available under Article Nr 223359 (not included)
Disponível desde Dezembro 2012
número de artigo 290730
unidade de venda 1 peça(s)
Body Basswood
Top Basswood
Frets 18
Neck Maple
Pickup Yes
B-Stock from € 45 disponível
€ 55
IVA incluído, € 20 de portes de envio adicionais
Em stock
Em stock

Este produto encontra-se em stock e pode ser enviado imediatamente.

Informações sobre o envio
Entrega entre aprox. Quinta, 4.04. e Sexta, 5.04.
1

191 Avaliações de clientes

4 / 5

Terá de iniciar sessão para classificar produtos.

Nota: De forma a prevenir que as classificações sejam baseadas em boatos, conhecimento limitado ou má publicidade nós apenas permitimos classificações provenientes de clientes no nosso website, que tenham adquirido o equipamento através de nós.

Após iniciar sessão poderá encontrar todos os produtos que poderá classificar em classificar produtos no centro de clientes.

características

som

acabamento

131 Críticas

M
Miguel1234 04.12.2017
assim que saiu da caixa, liguei ao amp, funcionou o primeiro acorde, depois disto não voltou a piar. muitas reviews apontavam para problemas de electronica e de ligações, mas não estava a espera que não funcionasse. adquirido já com esta situação em mente e com modificações previstas, no entanto volto a dizer, não estava a espera que não funcionasse.
a solução da thomann passa por devolver para receber um novo, que provavelmente virá igual, vou avançar já para as modificações que tinha em mente
características
som
acabamento
0
0
Reportar a crítica

Reportar a crítica

j
a bargain
jmateus 09.05.2022
bought it so i could play quietly, it fits the purpose, very easy to use ukulele.
características
som
acabamento
0
0
Reportar a crítica

Reportar a crítica

google translate gb
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
AM
Needs a few fixes and a setup- afterwards it is a (baby) rock dragon
Axel Morisson 11.12.2020
This is a nice looking and solidly crafted instrument. Note that I did not say "finely" crafted- that's where you come in.. It badly needs a string height adjustment as well as an intonation fix- and you can do this by loosening the strings and then gently pulling the plastic riser that should be the "bridge" from the riser. Then you can sculpt it with an x-acto knife to make its "edge" recede a bit and then re-test...in the end on mine I had to move the string contact point back some 1,5 mm and I did that by scraping at the plastic to create a new edge further back. In the end I got something that looks like a "compensated acoustic guitar bridge" -look it up for refference .A quick way of intonating an uke is using..matchsticks! Take a match and slide it behind the nut- so now the strings have a point of contact further back; if that improves tuning, you need a compensated nut made, or leave the matchstick in (you can cut from its thickness to tune). If it makes matters worse, and you need to lengthen the strings, then you must gently scrape te leading edge of the bridge towards the back (angling it slightly ,as if sharpening a blade or creating a cutting edge). Take good care to eventually round this edge with a bit of sandpaper once you are done, in order to avoid cutting the strings.Do this with the bridge off the instrument! place back, re-tune, re-test, and re-sculpt if necessary- I know it's a lot of work but you do not need toolmarks on the finish!
Before all that , WARNING! you should sort out string height first if necessary by filing the bottom of the bridge with a bit of sandpaper or a fine file.The strings on mine were a mile high and it was all due to a very high bridge. Once string height is set proceed with the intonation. Careful as you handle the bridge, the piezo element beneath it is responsible for all the sound in this instrument. It is not glued, it is just crammed in there tightly under it and it is delicate. Pull straight up on the bridge and on reinstalling do not press down too hard. After the intonation and string height are ok, here comes the hard electric re-building part: you will need either copper foil (gardener's shops carry it , for keeping snails at bay, or electronic part shops, or the *bay or the *zon..or..) or conductive paint. I recommend copper foil -has lower resistivity and also holds better in time, as conductive paint becomes less so in time once properly and totally dry. Wrap a narrow sheet of adhesive two faced auto sticky tape around the electronics cavity if the copper foil is not already adhesive on one side and complete the shielding by leaving a bit of a "lip" that goes out of the cavity and along the top so to make contact with the shielding stuck from the factory on the small plastic lid (there's a sliver metallic foil there). Add another bit of tape in electrical contact with the shielding done so far all around the walls of the output jack socket cavity and as always, leave a lip out so that when mounted, the jack plate itself screws in this conducting tape lip, completing the shielding. Warning: Do use a bit of NON conductive, insulating, etc tape (or even cellophane or paper adhesive tape) around the wires going to the jack and the exposed jack lugs , you do not want the shielding tape you just carefully installed to short out your signal.
Once that's over with, it should be finally tunable and quiet. Too quiet, in fact, as some rightly said. But the posters that described the electrical repairs in detail are totally correct : this thingie needs a total electrical makeover. Do not be afraid, although it sounds radical it is just about switching some wires around and switching the provided cap with a 1.5 nanofarad or 2 nF as they previously advised. For the correct wiring diagrams, search online for "gibson junior 50's wiring" for a good source of inspiration. Yes it is for "something else entirely" but it's a good example of a tone-volume stack for one pickup, and the grand total of parts is : one TONE capacitor- that you will exchange as previously discussed, one TONE POT - the linear one from the two on this little uke, and one VOLUME POT- make sure it is the logarithmic one . Yes these things are wired "bass ackwards"from the factory and you must correct that. Searching diagrams for gibson junior wiring will provide you with some four or five different variants- just observe where the pickup , output jack and capacitor goes and how the wires are soldered and where, and to the same regardless of what was previously in your little uke. In the end after all this work you are rewarded with a surprisingly good sounding instrument. After all these mods, you will be able to pass this through different amp sims and mod your sound in really sick ways, and yes this thing can "metal" for realz if all solder joints are correct... high gain amps? check! High volume with almost no buzz at all ? Check! Dead silent on clean between the notes ? And clear and adequately loud sound when playing these ontes? Check.
If the volume is still low or uneven across the strings, please loosen the strings and gently pull out the bridge once more, and look at the piezo pickup stuck underneath. It might have been pushed sidewise a bit and needs to be set dead center and not twisted . Re-place and put the bridge back vertically, gently, retune.. good luck! DO NOT pull on the little output shielded cable on one end of the piezo sensor, as the whole thing is very fragile and that particular connection is hard to repair. If nothing works for the volume, you might have a broken piezo pickup, and you can replace it with a standard one from the guitar shops, but you have to cut it to length (delicate operation) and re-do the insulation on the exposed end. If a violin piezo pickup is available (of the same "stick" under the bridge type) it might be possible to just drop it in without any modification. Keep the old broken part, take measurements before buying.. in the end you'll be happy with a real rock uke. A baby dragon!
características
som
acabamento
9
1
Reportar a crítica

Reportar a crítica

google translate gb
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
A
Harley Benton DC-UKE
Anónimo 05.09.2015
This was my first electric ukulele. Other than this, I have a mahalo soprano and a custom made banjolele. When I first opened the box, I was amazed at how beautiful this little uke is. The finish is much better than what you can see on the pictures and you can actually see some wood grain. I wasn't 10% pleased with the finish tough, as it had some scratches at the end of the neck. After playing it for a couple of days, I found it to be very confortable. There are no sharp fret ends, the neck is straight and it intonates perfectly till the 15th fret. After that, it's a little off, so I may try to adjust it. The factory strings are quite ok for an instrument this cheap. After they were broken in, the uke stays in tune quite well. I also love the neck. It's a quite chunky D-shaped neck. After plugging in and running it through my pedalboard, I found no additional noise. The piezo is quite harsh on the high end, so I use an EQ pedal to roll off the highs a bit. I have one complain about the controls. It's supposed to have 1 volume and 1 tone control. Mine seems to have 2 volume controls, since when I roll either one of them to zero, there is no volume. The tone would be very useful to tame the piezo. This is my only major complain. Overal, it's still an amazing ukulele for the price. It is NOT perfect nor comparable to mid to high end ukes, but holds its own against some 100?-200? solid body ukes on the market.
características
som
acabamento
8
0
Reportar a crítica

Reportar a crítica