ART DTI

461

Dual Transformer / Isolater

  • Hum Eliminator
  • Frequency response 10 Hz to 50 kHz
  • THD: 0.01%
  • 2 Channels
  • Inputs and unbalanced XLR balanced, TRS, RCA
  • Output as balanced XLR, jack unbalanced, RCA
  • Dimensions 44.5 mm x 107 mm x 89 mm
  • Weight 0.34 kg
Disponível desde Junho 2005
número de artigo 180511
unidade de venda 1 peça(s)
Multi-Channel Unit Yes
Channels 2
Active / Passive Passive
19" No
Pad switchable No
Gnd/Lift switchable No
Powered by battery No
Speaker Simulation No
B-Stock from € 73 disponível
€ 79
IVA incluído, € 20 de portes de envio adicionais
Em stock
Em stock

Este produto encontra-se em stock e pode ser enviado imediatamente.

Informações sobre o envio
Envio previsto até Sexta, 26.04.
1

461 Avaliações de clientes

4.3 / 5

Terá de iniciar sessão para classificar produtos.

Nota: De forma a prevenir que as classificações sejam baseadas em boatos, conhecimento limitado ou má publicidade nós apenas permitimos classificações provenientes de clientes no nosso website, que tenham adquirido o equipamento através de nós.

Após iniciar sessão poderá encontrar todos os produtos que poderá classificar em classificar produtos no centro de clientes.

características

som

acabamento

224 Críticas

A
Desapontado
Anónimo 05.10.2015
Depois de ler muitas informações sobre este produto achei que seria uma boa ideia comprar para reduzir alguns ruídos e aproveitar a possibilidade de poder ligar outputs diferentes de inputs.

Caraterísticas gerais: é um produto robusto, com bom acabamento, pequeno e facilmente manuseável para transportar sem problema.

Funcionamento: um desastre, não só não resolveu problema nenhum como acrescentou mais ruído e reduziu o nível sonoro para metade. Depois desta experiência deixei de usar e guardei numa gaveta.

Conclusão: mais um aparelho para ficar numa caixa e dinheiro mal gasto.
0
0
Reportar a crítica

Reportar a crítica

google translate gb
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
V
Verii 03.02.2019
I bought this device for XLR in, RCA out. Going by specifications it should be able to do this just fine, but it actually introduced noise rather than eliminate it. And not just a little, really loud too. Fiddled around a bit but found no solution. Balanced to SE is not this device's strong point...

For other set-ups it might work very well though. Just sharing my experience with this particular device. Too bad it didn't work too, competitor's transformers are MUCH more expensive!
6
1
Reportar a crítica

Reportar a crítica

google translate gb
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
K
Works like should
Kalleks 19.08.2019
Works very well for my configuration. There is no noise and the necessary bandwidth is available. The cable length is approximately 60 meters. An earth connection is a particularly good option.
3
1
Reportar a crítica

Reportar a crítica

google translate gb
Infelizmente ocorreu um erro. Por favor tente novamente mais tarde.
J
Invaluable peice of kit
Johnf52 22.06.2015
I have two of these and will probably end up with more! Hum loops can be a pain when setting up a PA rig in "unknown territory" and it wouldnt be the first time that earth wires have been temporarily removed from mains plugs etc, which whilst solving one problem creates another with regards to potential safety. These little beaties put all that behind us. With just about every possibly combination of in and out through phono, jack and xlr you can isolate 95% of all known audio connections. It is also possible with a little cunning to use it as a balanced signal generator/splitter, by using a short phono to phono link on the input side a single xlr or jack input can be fed to both internal transformers producing two separate, balanced outputs. A trick I have used a few times now.

Sturdy and well built a couople of these should be in every sound techs "goody bag"
1
1
Reportar a crítica

Reportar a crítica