Audix D-Clip

57

Microfoonhouder

  • Voor Audix D serie
  • Draaigewricht
  • 3/8'' schroefdraad
  • Kleur: zwart
Leverbaar sinds Januari 2008
artikelnummer 139136
verkoopseenheid 1 stuk
Component type Microphone Clamp
€ 16,90
Incl. btw plus € 5,90 verzending
direct leverbaar
direct leverbaar

Dit product is op voorraad en kan direct verzonden worden.

Informatie over de verzending
Levering verwacht rond Maandag, 29.04.
1

57 Klantenbeoordelingen

4.7 / 5

U moet ingelogd zijn om producten te evalueren.

Note: Om te voorkomen dat evaluaties gebaseerd zijn op roddel, geruchten of heimelijke advertentie staan wij op onze website alleen evaluaties toe van daadwerkelijke gebruikers die het geevalueerde product bij ons gekocht hebben.

Na inloggen vindt u alle producten die u kunt evalueren ook onder “Product evalueren” in uw klantencentrum.

afwerking

29 Recensies

A
Audix D2 clipje kwijt.
Anoniem 09.10.2016
Als je het clipje kwijt bent van één van je favoriete microfoons, wat moet je dan? Dan bestel je een nieuwe originele. Perfect fit en fantastisch om een draaiknop te hebben om je hoek bepaling strak te zetten.

Er zit al een van 5/8" naar 3/8" verloopnippel in, die hoef je er dus niet bij te bestellen. Erg fijn!
afwerking
0
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
P
D-Clip Madness
PDJMDS 13.11.2018
Well, apparently I can win a prize for writing a review of a mic clip so here it is.
The way in which the mic just slots in is just magical, enhancing the fundamental with precision and that warmth you can only get from an analog mic clip. (I've tried digital mic clips, I know what I'm talking about, my studio is full analog)
On adjusting the angle and hence the aspect of the diaphragm the silk in the highs just magically appears where as the harsh high mids are tempered beautifully.
The accuracy of this Mic clip is second to none, I might even but another just to have it in the rack for those special occasions.
The only thing that is better in my experience is the solid state valve mic clip manufactured by Telefunken in 1956, but good luck finding one of them for less than 5000¤.
Buy one NOW
afwerking
10
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
A
Solid plastic with firm grip
Anoniem 13.01.2017
This is a simple item that works well. It fits small barrelled microphones into the clip holder. Instead of sliding the microphone down into the bracket, you push against it and it grabs it in.

The plastic is solid and feels sturdy. It would break under serious abuse but probably nothing less. The angle adjustment knob is tight fitting and holds relatively well. Under determined force the clip angle sags. However, and more importantly, when holding a microphone it does not droop down.

This is perfect for my AKG D112 (without built-in clip) and holds it steady against the blasts of air emitted from kick drums.
afwerking
1
0
Evaluatie melden

Evaluatie melden

google translate gb
Helaas is er een fout opgetreden, probeert u het a.u.b. later nogmaals.
TG
Stong and fits Neumann km series
Tony Guitar 23.01.2022
Good clip. Fits Neumann km series and probably a lot of others. Thumb screw is a little bulky but very well built.
afwerking
0
0
Evaluatie melden

Evaluatie melden